Monthly Archives: November 2016

Trial order of corrugated pyramid shaker screen from Nigeria

Trial order of pyramid shaker screen will flying to Nigeria this morning. This is only a simple which we send to them. The use of corrugated pyramid screens on a dryer in second stage mud and cuttings cleaning helped recover a large volume of oil-based drilling mud to save more than $60,000 in mud costs.

img_0366

DC Machinery Company has again revolutionized screening technology with the introduction of the patented Pyramid (PMD) and Pyramid Plus (PMD+) screens. This revolutionary three dimensional screen design offers the benefits of traditional flat screens while adding a significant increase in useable screen area; allowing for a 70% increase in fluid handling capacity.

img_0367

Benefits of Pyramid Screens compare with the flat screens:

1. Increased Shaker Capacity—Pyramid and Pyramid Plus screens increase the total amount of useable screen area by 50% to 125%.
2. Screen Finer Faster—Utilizing Pyramid or Pyramid Plus screens enables rigs to screen 2 to 3 mesh sizes finer than traditional perforated plate panels. This maximizes solids removal capacities.
3. Makes Fine Separations—Pyramid and Pyramid Plus screens are capable of making separations as fine as 43 microns.
4. Easily Repaired—The Pyramid screen design lends itself to easy field repair with RTV products.

Pyramid screens provide an easy, cost effective increase in shaker performance. Designed with the latest technology, Pyramid screens allow rigs to screen finer earlier in the drilling process, thus significantly reducing mud and disposal costs.

Lowestline price of mud guns from DC Machinery

Mud gun is another equipment for agitating drilling mud or fluid during mud process. It is mounted on mud tanks. DC Machinery 2 models of mud guns 2″ and 3″.

For many years, mud guns were used as the sole means of agitation. These devices usually carry mud from a down stream comapartment and spray it into an up-stream compartment to keep solids suspended. However, the true mixing effect of mud guns tends to be localized around the point where the nozzle may add 100-200 GPM of mud into the tank above and beyond the normal flow from the well.

mud-guns

DC Mud gun features

1. DCMud gun main feature is the mud gun nozzles are made of rubber. This is different with other mud guns. This rubber nozzle can be more durable and longer usable life.
2. Mud guns from DC make it more efficient than the sharp shoulder in a 3 to 1 reducers. Well, under this feature we get increased blending and agitation
3. DC mud gun is usually with only 1 nozzle. However, it can rotate as 270 degree.

DC produces the mud gun with good spray effect , large clean area , simple structure, flexible operaion and easy to use. In order to extend the sale market, All DC solid control enjoye a bigeest discount from Dec to the new year. Welcome to your inquires.

Structure Details of DC Mud tank For Solid Control System

Mud tank is the supporting unit in solid control system. Mud tanks can be divided into mixing tank, shale shaker tank, centrifuge tank, degasser tank, trip tank and ect. Different function mud tank located different equipment.

Mud tanks main body are welded together with steel plate and steel pipe,rails top and walk way is made of steel grid and antiskid plate.Guard rail material is square pipe,rail are foldable type.Stairs are made of antiskid plate.Two sides rail have pins for steady and safe walk.Mud tanks in whole mud system will have special device to clean mud tank and equipments.

SONY DSC

SONY DSC

DC Drilling mud recycling tank adopts centralized electric control, heating and heat preservation system applied for tank body in a polar regions, the oilfield mud tanks produced by DC have the feature advantages in drilling site: ensuring no mud loss, reducing environmental pollution, lowering labor intensity and satisfying drilling requirements timely through mud mixing.

DC tanks are widely used in oil and gas drilling field,HDD,CSM exploration,slurry separation,etc. DC is capable of providing customers with series products ,such as oil & gas drilling fluid solids control equipment, decanter centrifuge, drilling waste management equipment and drilling security equipment.

Daily maintenance of DCZCQ vacuum degasser

DCZCQ advanced degassers are designed to remove virtually all entrained gases—including hydrogen sulfide and corrosive oxygen—from drilling fluids. These degassers reduce the threat of dangerous and costly blowouts caused by recirculating gas-cut mud.

The maintenance of vacuum degasser for drilling fluid processing in daily use is more important than the repair after it breaks down. So I’d like to introduce several tips about the maintenance.

vacuum-degasser

Firstly, the vacuum degasser for drilling fluid processing should be washed after use. The rotor and the suction pipe in the vacuum tank should be cleaned. You should cut off the power supply, remove the blocking plate of the hole, and check components whether it is damage or not. You could wash the tank wall and the rotor by using high-pressure pipe. All the cleaning work should be done after each use to ensure the normal use.

Secondly, the top cover of vacuum tank should be cleaned once a week in order to avoid debris blocking the gas channel. When it is washed by water, you should rinse off the vacuum line and remove the screw plug and table seat. High pressure pipe is inserted into it for 3~5 minutes each time.

Thirdly, for the vacuum pump, you should always check working condition of bearing and lubrication condition. The bearing is 15~20 degrees higher than ambient temperature on normal working condition. When working temperature of vacuum degasser for drilling fluid processing is higher than 30 degrees, you should always check the vacuum gauge, replace water in separator of steam and water in time, and maintain the water temperature less than 35 degrees.

DCLW 450-1000N decanter centrifuge got to TianJin Railway station

Yesterday, we shipped a DCLW450-1000N decanter centrifuge to TianJin Railway station which will be used in cold area Siberia drilling site.

The DCLW450-1000N decanter centrifuge is a common model of used for drilling field. Usually, the centrifuge located after deslter to separate out of 5-7um solid phase particles.
decanter-centrifuge

Features of the DCLW450-1000N decanter centrifuge:
1. With 40m3/h big treating capacity.
2. Simplified solid control system, low energy consumption , lighter working load, and the purification efficiency increased by 30% than original.
3. Reasonable slenderness ratio.
3. Optimized the settling zone parameters and feeding mode, enhanced the centrifuge sand removing effect, performance can be comparable to the same specifications of the imported centrifuge .

DC production drilling fluid centrifuge has high purification efficiency, convenient adjustment and easy maintenance. We also can design and manufacture different fields centrifuges, such as waster water processing, chemical, food and ect.

More Benefits and Features of DCTLL-A915 Cuttings Dryer

Due to increasingly stringent environmental requirements around the world, the cost impact of waste management for oil based drilling operations is steadily increasing. This puts a large focus on the ability to efficiently clean, transport, and dispose of cuttings, while maximizing fluids recovery.

SONY DSC

SONY DSC

DCTLL-A915 Cuttings Dryer has been proven to provide a dramatic reduction in drill solids waste discharge and to help maximize the recovery of synthetic-, oil-, or ester-based drilling fluids. The unit has also been proven to help operators meet environmental compliance requirements such as the EPA requirements for discharge and also reduce the volumes of drilling waste that has to be transported from a drilling location for disposal.

Benefits and Features
1. High capacity unit is capable of supporting operations with a high rate of penetration (ROP) – average 40-60 TPH.
2. Proven reliable technology, well average can achieve below 5% OOC.
3. Versatile layout and relatively small footprint allowing for easy configuration into fixed installations, winterized modules, or can be mounted on a trailer for easy mobility.
4. Reduces volumes of waste to haul off for transportation and disposal by 40%

in addition to the above, the advantages of the DCTLL-A915 Cuttings Dryer are adaptable, better treating efficiency, stable working, long service life and can effective recyling the drilling fluid in drilling cuttings. It is the preferred equipment to dry drilling cuttings, recycle drilling fluid and especialy recycle oil base drilling fluid.

Many sets mud cleaner and shale shaker finished the production

According to 30 days overtime manufacturing, DC Machinery have already finished the production of 12 sets mud cleaners and 8 sets shale shakers.

The DCS700-3 shale shaker is the primary processing equipment in solids control system, used for separating larger cuttings from drilling mud, and it plays an important role in protecting drilling fluid performance. The shale shakers produced by DC Machinery have the advantages of large handling capacity, screening high precision, low-energy, environmental protection and so on.

shale-shaker-and-mud-cleaner

The Mud cleaner is combined with 2 pcs 10″ hydrocyclone and 12pcs 4″hydrocyclone and DCS7003 bottom shaker. It occupys small space and the function is powerful , mud cleaner is the ideal device of the second class and the third class solid control to treat the drilling mud.

DC Solids Control is thet professional manufacturer of Solids Control System in China, DC is a vital part of the world hydrocarbon exploration and production industry, as well as one of top three solids control equipment suppliers in China, which offers its products for CNPC, CNOOC ,HH, Gazprom, RG, etc . If you want to know more information about solid control system and oil drilling solids control equipment,you can contact us online.

Drum and screw together of decanter centrifuges

Drum and screw together is the key part of decanter centrifuges. The screw of a decanter (solid wall screw centrifuge) serves to discharge the solid material from the drum and can, depending on the application, be performed differently.

Thus, in the event of abrasive media, various forms of wear protection can be added to the screw helix. Furthermore, for sanitary applications or for sticky products, the screw helix can, if necessary, be relief ground.

centrifuge

There are also different versions with respect to the gap of the screw helix (screw pitch) to each other and with respect to the number of screw flights.

In addition there are different designs with respect to the form and position of the holes or slits, through which the medium to be centrifuged is fed into the decanter drum.

DC Customized Mud Recycling System for HDD

Horizontal directional drilling short name is HDD. HDD technology has the obvious in oil and gas pipelines crossing the rivers, lakes, highway, railway hub and other obstacles and important area.

Relative to the use of drilling fluids within the oil &gas industry, the use of drilling fluids within the horizontal directional drilling (“HDD”) industry, is new. As the use of HDD technology did not become mainstream until the 1980’s, it took another decade before drillers started to consider the use of basic drilling fluids. Even today, the amount of research and development aimed at HDD drilling fluids is considered a rounding error in the oligopoly of drilling fluid manufacturers.

SONY DSC

SONY DSC

HDD Mud Recycling System is made up of drilling rig mouth to return to mud of the ground through the mud into the mud pit, using liquid slurry pump or vertical sand pump the submersible supply to shale shaker,and then male the shale shaker removing out of solid phased particles, the processed mud fall into the mud tank having many separate space.

DC Solids control as drilling waste management company is dedicated to supply different kinds of drilling fluids recycle units such as shale shaker, de sander, de silter, centrifugal pump and hopper. Also, we provide the complete system matching with different size of rig from 150GMP mini system to 2000GPM large system.